Damage localization in complex composite panels using guided wave based structural health monitoring system

Yingtao Liu, Seung Bum Kim, Aditi Chattopadhyay, Derek Doyle

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

Knowledge of the damage location in composite structures is a necessary output for both Non-Destructive Evaluation (NDE) and Structural Health Monitoring (SHM). Although several damage localization approaches using a triangulation method and Time-of-Flight (ToF) of guided waves have been reported in literature, the damage localization technique is still not mature for composite structures with complex material properties, varying thickness and complex geometries. This paper investigates the development of a new approach for SHM and damage localization using a guided wave based active sensing system. In contrast to the traditional ellipse method, the proposed method does not require the information of structural thickness, ToF, or the estimation of group velocities of each guided wave mode at different propagation angles, which is one of the main limitations of most current ToF methodologies involving composites. This approach uses time-frequency analysis to calculate the difference of the ToF of the converted modes for each sensor signal. The damage location and the group velocity are obtained by solving a set of nonlinear equations. The proposed method can be used for composite structures with unknown lay-up and thickness. To validate the proposed method, experiments were conducted on both composite plates and stiffened composite panels. Eight piezoelectric (PZT) transducers were surface-bonded on each composite specimen and used in four pairs. The PZT transducers in each pair were bonded close to each other. In the PZT array, one PZT transducer from one PZT pair was used as the actuator and the other three pairs were used as sensors. A windowed cosine signal was used as the excitation signal. The locations of the delaminations in the composite specimens were validated using a flash thermography system. The accuracy of the proposed method in localizing delaminations was examined through comparison with the experimental measurements.

Original languageEnglish (US)
Title of host publicationASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011
Pages495-501
Number of pages7
Volume2
StatePublished - 2011
EventASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011 - Scottsdale, AZ, United States
Duration: Sep 18 2011Sep 21 2011

Other

OtherASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011
CountryUnited States
CityScottsdale, AZ
Period9/18/119/21/11

Fingerprint

Guided electromagnetic wave propagation
Structural health monitoring
Piezoelectric transducers
Composite structures
Composite materials
Delamination
Sensors
Triangulation
Nonlinear equations
Materials properties
Actuators
Geometry
Experiments

ASJC Scopus subject areas

  • Civil and Structural Engineering
  • Biomaterials

Cite this

Liu, Y., Kim, S. B., Chattopadhyay, A., & Doyle, D. (2011). Damage localization in complex composite panels using guided wave based structural health monitoring system. In ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011 (Vol. 2, pp. 495-501)

Damage localization in complex composite panels using guided wave based structural health monitoring system. / Liu, Yingtao; Kim, Seung Bum; Chattopadhyay, Aditi; Doyle, Derek.

ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011. Vol. 2 2011. p. 495-501.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Liu, Y, Kim, SB, Chattopadhyay, A & Doyle, D 2011, Damage localization in complex composite panels using guided wave based structural health monitoring system. in ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011. vol. 2, pp. 495-501, ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011, Scottsdale, AZ, United States, 9/18/11.
Liu Y, Kim SB, Chattopadhyay A, Doyle D. Damage localization in complex composite panels using guided wave based structural health monitoring system. In ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011. Vol. 2. 2011. p. 495-501
Liu, Yingtao ; Kim, Seung Bum ; Chattopadhyay, Aditi ; Doyle, Derek. / Damage localization in complex composite panels using guided wave based structural health monitoring system. ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011. Vol. 2 2011. pp. 495-501
@inproceedings{f12233a362434073986f54d6917448bb,
title = "Damage localization in complex composite panels using guided wave based structural health monitoring system",
abstract = "Knowledge of the damage location in composite structures is a necessary output for both Non-Destructive Evaluation (NDE) and Structural Health Monitoring (SHM). Although several damage localization approaches using a triangulation method and Time-of-Flight (ToF) of guided waves have been reported in literature, the damage localization technique is still not mature for composite structures with complex material properties, varying thickness and complex geometries. This paper investigates the development of a new approach for SHM and damage localization using a guided wave based active sensing system. In contrast to the traditional ellipse method, the proposed method does not require the information of structural thickness, ToF, or the estimation of group velocities of each guided wave mode at different propagation angles, which is one of the main limitations of most current ToF methodologies involving composites. This approach uses time-frequency analysis to calculate the difference of the ToF of the converted modes for each sensor signal. The damage location and the group velocity are obtained by solving a set of nonlinear equations. The proposed method can be used for composite structures with unknown lay-up and thickness. To validate the proposed method, experiments were conducted on both composite plates and stiffened composite panels. Eight piezoelectric (PZT) transducers were surface-bonded on each composite specimen and used in four pairs. The PZT transducers in each pair were bonded close to each other. In the PZT array, one PZT transducer from one PZT pair was used as the actuator and the other three pairs were used as sensors. A windowed cosine signal was used as the excitation signal. The locations of the delaminations in the composite specimens were validated using a flash thermography system. The accuracy of the proposed method in localizing delaminations was examined through comparison with the experimental measurements.",
author = "Yingtao Liu and Kim, {Seung Bum} and Aditi Chattopadhyay and Derek Doyle",
year = "2011",
language = "English (US)",
isbn = "9780791854723",
volume = "2",
pages = "495--501",
booktitle = "ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011",

}

TY - GEN

T1 - Damage localization in complex composite panels using guided wave based structural health monitoring system

AU - Liu, Yingtao

AU - Kim, Seung Bum

AU - Chattopadhyay, Aditi

AU - Doyle, Derek

PY - 2011

Y1 - 2011

N2 - Knowledge of the damage location in composite structures is a necessary output for both Non-Destructive Evaluation (NDE) and Structural Health Monitoring (SHM). Although several damage localization approaches using a triangulation method and Time-of-Flight (ToF) of guided waves have been reported in literature, the damage localization technique is still not mature for composite structures with complex material properties, varying thickness and complex geometries. This paper investigates the development of a new approach for SHM and damage localization using a guided wave based active sensing system. In contrast to the traditional ellipse method, the proposed method does not require the information of structural thickness, ToF, or the estimation of group velocities of each guided wave mode at different propagation angles, which is one of the main limitations of most current ToF methodologies involving composites. This approach uses time-frequency analysis to calculate the difference of the ToF of the converted modes for each sensor signal. The damage location and the group velocity are obtained by solving a set of nonlinear equations. The proposed method can be used for composite structures with unknown lay-up and thickness. To validate the proposed method, experiments were conducted on both composite plates and stiffened composite panels. Eight piezoelectric (PZT) transducers were surface-bonded on each composite specimen and used in four pairs. The PZT transducers in each pair were bonded close to each other. In the PZT array, one PZT transducer from one PZT pair was used as the actuator and the other three pairs were used as sensors. A windowed cosine signal was used as the excitation signal. The locations of the delaminations in the composite specimens were validated using a flash thermography system. The accuracy of the proposed method in localizing delaminations was examined through comparison with the experimental measurements.

AB - Knowledge of the damage location in composite structures is a necessary output for both Non-Destructive Evaluation (NDE) and Structural Health Monitoring (SHM). Although several damage localization approaches using a triangulation method and Time-of-Flight (ToF) of guided waves have been reported in literature, the damage localization technique is still not mature for composite structures with complex material properties, varying thickness and complex geometries. This paper investigates the development of a new approach for SHM and damage localization using a guided wave based active sensing system. In contrast to the traditional ellipse method, the proposed method does not require the information of structural thickness, ToF, or the estimation of group velocities of each guided wave mode at different propagation angles, which is one of the main limitations of most current ToF methodologies involving composites. This approach uses time-frequency analysis to calculate the difference of the ToF of the converted modes for each sensor signal. The damage location and the group velocity are obtained by solving a set of nonlinear equations. The proposed method can be used for composite structures with unknown lay-up and thickness. To validate the proposed method, experiments were conducted on both composite plates and stiffened composite panels. Eight piezoelectric (PZT) transducers were surface-bonded on each composite specimen and used in four pairs. The PZT transducers in each pair were bonded close to each other. In the PZT array, one PZT transducer from one PZT pair was used as the actuator and the other three pairs were used as sensors. A windowed cosine signal was used as the excitation signal. The locations of the delaminations in the composite specimens were validated using a flash thermography system. The accuracy of the proposed method in localizing delaminations was examined through comparison with the experimental measurements.

UR - http://www.scopus.com/inward/record.url?scp=84859526258&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84859526258&partnerID=8YFLogxK

M3 - Conference contribution

AN - SCOPUS:84859526258

SN - 9780791854723

VL - 2

SP - 495

EP - 501

BT - ASME 2011 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2011

ER -